Pipes

PIPES ~ HEADERS & Etc.

Our pipe assembly comes with the following:

Standard high temp baked on coating, flex, springs and O- rings.

Standard length flex is 2 5/8" and can be ordered n any length.

This is one of the best pipes on the market for racing, numerous records have been set using our pipe. Our pipes are de-burred internally which provides an un-obstructive path for the resonating waves.

Our pipe is available with Internal or External stinger. The Internal pipe needs no muffler. The External pipe needs an external muffler added to be race noise level legal.

OVER SEA'S SHIPPING QUOTE - Click Here

B.H. HANSON

ORDER HERE

From left to right.

ORDER HERE

1-Tuned Pipe Cone to Cone-To be used with wrap to center (WTC) and deep v headers. Also good for 231 engines and high RPM 260 engines - $85

2-Tuned Pipe 1 inch band - To be used with 260 engines and all headers *EXCEPT* wrap to center and deep v - $85

3-Tuned Pipe 2 inch band - To be used with 260 engines and all headers *EXCEPT* wrap to center and deep v -$85

4-Tuned Pipe - Super Quiet -( Far Righ) To be used with all engines. Measures 78 DB at 50 feet while still providing outstanding Horse Power - $175. PIPE ONLY

HEADERS - All headers are $38 - ORDER HERE

New Header #15

New Header #16

1. 90 Deg. header with 3 inch offset and 90 Deg. bend	8. Wrap to center header. Puts the header at center of boat.
2. 90 Deg. header with 2 inch offset and 90 Deg. bend.	9. 90/90 header with 1 inch offset and 2 1/2 inch rise
3. 90 Deg. header with 1 inch offset and 90 Deg. bend.	10. 45/90 header with one inch offset and one inch rise.
4. 100 Deg. header with one inch offset and 100 Deg. bend.	11. 45/90 header with one inch offset and one inch drop
5. 105 Deg. header with one inch offset and 105 deg bend.	12. 90 Deg. header with 25 Deg. angle down , one inch drop and 4 inch offset
6. Wrap to flush header will put pipe approximately 1 3/4 inch from engine centerline.	13. 90 Deg. header with 25 Deg. angle down, one inch drop and 3 inch offset
7. Deep V header. header with approximately 3 1/2 inch offset to put header in left side of boat.	14. 90 Deg. header with 25 Deg. angle down, one inch drop and 2 inch offset

15. The same as #6 with the exception of a 98 degree angle to allow you to adjust your tuned pipe to the proper length using band pipes and still exit in the center of your boat. Will fit in some applications where a center exit is required and needs to exit from a center turbine style cowl.
	#15 on Right #6 on Left
	16. Outboard Rear Exhaust Header Motor, Lower Unit & Stand NOT Included

Headers ~ Exhaust Flange & Muffler

ORDER HERE

Tuned Pipe System $165

Includes Pipe, Exhaust Flange & choice of any header NOTE #5 NOT Included

ORDER HERE

Each part can be bought individually as described below

1- TP-1000 (cone to cone) & TP-L1000(2-inch band) Tune Pipe. The BEST on the market! Holds all nation and world gasoline speed records - $85	6 - V-1500H Wrap-to-Flush Exhaust Header - $38
2 - EF-3100 Two-piece Header Flange with Viton O-Rings - The flange supports one of our four headers in a water-cooled environment, enabling the exhaust to remain cool and dry - $45	7 - V-1000H 90 degree Exhaust Header - $38
3 - Deep V-6000H inside hull Pipe Header - $38	8 - V-9000H 100 degree Exhaust Header - $38
4 - CH-5000H Wrap-to-Center Cat Hydro Header - $38	9 - V-1000H 3" 90 degree Exhaust Header - $38
5 - MF-100 Billet Stinger Muffler. May be taken apart, cleaned, and elements replaced - $36	10 - V-1000H 90 degree 2" Riser Exhaust Header - $38